Special combo set
120pcs fiber discs Ø180mm
+ backing pad and grinder FREE

Angle Grinder WX-18001:

Locking the mains switch in the on position:
if needed, it is not necessary to keep your fingers on the switch while working

Rear handle with a rubberized surface for attachment and front additional handle with the possibility of attachment in three positions:
significantly reduces the values of vibrations transmitted from the sander to the hands, enabling comfortable work even for left-handed people

Spindle lock button:
It makes easier to change the disc by blocking the rotation of the spindle

Gearbox made of light alloy:
It reduces the weight of the sander

Simple replacement of carbon brushes:
without intervention in the sander

Angle Grinder WX-18001:

"SOFT START" function:
ensureing a smooth, soft start of the motor and reducing the starting torque when starting the grinder

"RESTART PROTECTION" function:
protection against restarting the engine after the power supply is restored

"KICK BACK STOP" function:
It shuts off the engine when the disc is blocked and protects the operator from kickback

Two-position mains switch:
the design of the switch protects against accidental starting of the grinder when grasping the rear handle

Double insulation:
increased protection against electric shock

Crack-resistant protective disc cover:
with the option of setting the optimal position for greater safety

Angle Grinder WX-18001:

Electronic protection against overload:
when the set temperature level is exceeded, the motor switches off

Self-disconnecting carbon brushes:
Protecting the rotor commutator from damage at the end of the life of the carbon brushes

Gearbox made of light alloy:
The material used contains additives that increase resistance to wear

Motor winding with epoxy protection:
It contributes to a longer life of the grinder

Effective anti-dust system:
It reduces the penetration of dust during the intake of cooling air

Specially shaped air inlets:
Increasing the efficiency of engine cooling

Fibre sanding disc for steel HERMAN FS-10:


Primary raw material - layer of abrasive aluminium oxide grains (industrially produced corundum) bonded with synthetic resin to a 0.8mm thick vulcanised fibre backing:
very good removal especially when machining standard strength steel

Necessity of using a backing plate:
the properties of the backing plate (hardness, elasticity) are decisive for the type of work to be carried out and the design of the backing plate is a key factor for safety at work

Grain size standard in the range P24 to 80 according to FEPA (850 to 200 µm):
allows the selection of the appropriate tool from coarse sanding to finer cleaning

Fibre sanding disc for stainless steel HERMAN FR-10:


Primary raw material - layer of abrasive zirconium grains (80%) bonded by synthetic resin to a 0.8mm thick vulcanised fibre backing:
very good removal especially when machining stainless steel, higher strength steels etc.

Necessity of using a backing plate:
the properties of the backing plate (hardness, elasticity) are decisive for the type of work to be carried out and the design of the backing plate is a key factor for safety at work

Grain size standard in the range P24 to 80 according to FEPA (850 to 200 µm):
allows the selection of the appropriate tool from coarse sanding to finer cleaning

Fibre sanding disc for stainless and alloy steels HERMAN FX-10:


Primary raw material - layer of abrasive ceramic grains (100%) bonded with synthetic resin to a 0.85mm thick vulcanised fibre backing:
very good removal especially when machining stainless steel, alloy steels, etc.

Necessity of using a backing plate:
the properties of the backing plate (hardness, elasticity) are decisive for the type of work to be carried out and the design of the plate is a key factor for safety at work

Grain size standard in the range P24 to 80 according to FEPA (850 to 200 µm):
allows the selection of the appropriate tool from coarse sanding to finer cleaning

Backing pad for fibre discs:


Large metal clamping nut with M14 thread:
secure fixing on angle grinder shaft

Made of Flexithan 55 modified thermoplastic rubber:
high safety of design, resistance to oils, lubricants and also to ageing over time

Stable properties over a wide temperature range:
slight change in properties occurs at ambient temperatures below -20°C and with prolonged sanding and overheating of the pad to temperatures above 120°C

Manufactured according to ISO 15636:
standard for the design and clamping of vulcanised fibre sanding discs